Help With Small Motor...

[Klay Anderson]

The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.

 

[Bob F]

On 12/15/2022 3:05 PM, Klay Anderson wrote:
> The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

I would recommend starting by trying to get any tiny motion turning
either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Bob F]

On 12/15/2022 3:05 PM, Klay Anderson wrote:
> The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

I would recommend starting by trying to get any tiny motion turning
either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Bob F]

On 12/15/2022 3:05 PM, Klay Anderson wrote:
> The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

I would recommend starting by trying to get any tiny motion turning
either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Peter W.]

On Thursday, December 15, 2022 at 7:50:59 PM UTC-5, Bob F wrote:

On 12/15/2022 3:05 PM, Klay Anderson wrote:
The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

All good as is what follows. However, I would go with standing the motor rotor-up and putting some Kroil, Penetrating Oil or some similar material onto the shaft end and let it sit for 24 hours before attempting to remove the impeller. Further, if you can clamp the pump in some way as to render it rigid, it would make the process easier. As these things go, typically, impeller removal is not overly difficult if the shaft has not corroded such that it has swollen into the impeller. And when you put it back together, a we touch of anti-seize would not go amiss.

Peter Wieck
Melrose Park, PA

 

[Peter W.]

On Thursday, December 15, 2022 at 7:50:59 PM UTC-5, Bob F wrote:

On 12/15/2022 3:05 PM, Klay Anderson wrote:
The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

All good as is what follows. However, I would go with standing the motor rotor-up and putting some Kroil, Penetrating Oil or some similar material onto the shaft end and let it sit for 24 hours before attempting to remove the impeller. Further, if you can clamp the pump in some way as to render it rigid, it would make the process easier. As these things go, typically, impeller removal is not overly difficult if the shaft has not corroded such that it has swollen into the impeller. And when you put it back together, a we touch of anti-seize would not go amiss.

Peter Wieck
Melrose Park, PA

 

[Peter W.]

On Thursday, December 15, 2022 at 7:50:59 PM UTC-5, Bob F wrote:

On 12/15/2022 3:05 PM, Klay Anderson wrote:
The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

All good as is what follows. However, I would go with standing the motor rotor-up and putting some Kroil, Penetrating Oil or some similar material onto the shaft end and let it sit for 24 hours before attempting to remove the impeller. Further, if you can clamp the pump in some way as to render it rigid, it would make the process easier. As these things go, typically, impeller removal is not overly difficult if the shaft has not corroded such that it has swollen into the impeller. And when you put it back together, a we touch of anti-seize would not go amiss.

Peter Wieck
Melrose Park, PA

 

[Phil Allison]

Bob F wrote:
-------------------
> On
12/15/2022 3:05 PM, Klay Anderson wrote: > > The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
------------

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.


...... Phil.


I would recommend starting by trying to get any tiny motion turning

either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Phil Allison]

Bob F wrote:
-------------------
> On
12/15/2022 3:05 PM, Klay Anderson wrote: > > The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
------------

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.


...... Phil.


I would recommend starting by trying to get any tiny motion turning

either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Phil Allison]

Bob F wrote:
-------------------
> On
12/15/2022 3:05 PM, Klay Anderson wrote: > > The album <https://imgur.com/a/6wgKqmj> shows a small motor and impeller from a water pump. I cannot figure out how to get the impeller off as the other end of the shaft is enclosed. I am trying to replace the bearing. Google is not helpful. Thank you.
------------

It looks like it is designed for you to hold the impeller and turn the
shaft with a flat blade screwdriver. The blade slot is a little chewed
up, so make sure you have a really well fitting screwdriver to match the
slot.

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.


...... Phil.


I would recommend starting by trying to get any tiny motion turning

either way, then work it carefully a tiny bit at a time, turning back
and forth, going a little looser, lightly tighter over and over again to
work the threads free without mutilating the screwdriver slot.

 

[Peter W.]

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.

The threads will be set to tighten the impeller in the normal spin direction. So, to remove it, turn it in the running direction.

Peter Wieck
Melrose Park, PA

 

[Peter W.]

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.

The threads will be set to tighten the impeller in the normal spin direction. So, to remove it, turn it in the running direction.

Peter Wieck
Melrose Park, PA

 

[Peter W.]

** Looks like a special driver is needed, one with a centre pin and two flats.
Also watch out for the thread to be reverse to normal.

The threads will be set to tighten the impeller in the normal spin direction. So, to remove it, turn it in the running direction.

Peter Wieck
Melrose Park, PA