AV Sender interference

[felix_unger]

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

 

[atec77]

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?

--









X-No-Archive: Yes

 

[Petzl]

On Sat, 25 Feb 2012 12:22:16 +1000, atec77 <"atec77 "@hotmail.com>
wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?

The one I had had five channels to choose from
--
Petzl
Million: 1,000,000
Billion: 1,000,000,000
Trillion: 1,000,000,000,000
Quintillion: 1,000,000,000,000,000,000
Sextillion: 1,000,000,000,000,000,000,000
Nonillion: 1,000,000,000,000,000,000,000,000,000,000
Centillion: 1 followed by 303 zeros

 

[John G]

felix_unger was thinking very hard :

I have a good AV sender. The picture is great, except that because it's on
the 2.4ghz band I get a lot of interference. Does anyone know any way to
filter the signal? The AC is filtered via a power board. Or alternatively can
anyone recommend a VERY good sender with IR control that isn't subject to
audio/video interference? I have tried the Strong 5.8ghz one, and the Cocoon
digital and 2.4 ghz models, and none are as good as the one I have, which is
On-for-All brand. thanks.

Have you tried turning your Cordless Phone Off?
I know you want to use it but I found the phone to be the source of the
interference and on the rare occasion I need video repeater I can do
without the phone.

--
John G

 

[felix_unger]

On 25-February-2012 2:55 PM, John G wrote:

felix_unger was thinking very hard :
I have a good AV sender. The picture is great, except that because
it's on the 2.4ghz band I get a lot of interference. Does anyone know
any way to filter the signal? The AC is filtered via a power board.
Or alternatively can anyone recommend a VERY good sender with IR
control that isn't subject to audio/video interference? I have tried
the Strong 5.8ghz one, and the Cocoon digital and 2.4 ghz models, and
none are as good as the one I have, which is On-for-All brand. thanks.

Have you tried turning your Cordless Phone Off?
I know you want to use it but I found the phone to be the source of
the interference and on the rare occasion I need video repeater I can
do without the phone.

yes, but it's on 5.8ghz anyway.

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

"Julia finally got something right. Older people don't vote Labor, because they have seen too many incompetent, mismanaging, money-wasting Labor governments"

“It doesn't matter [who the leader is] the Labor Party is rotten, the policies stink, the lies insufferable, and the waste intolerable. The Muppets could do a better job!”

“All that's needed now is a small miracle to rid us of the worst prime minister and the worst government in Australia's history”

"If the WORLD as a whole cut ALL emissions tomorrow, the average temperature of the planet's not going to drop for several hundred years, perhaps over on thousand years" - Tim Flannery, Climate Commissioner

"It is a remarkable fact that despite the worldwide expenditure of perhaps US$50 billion since 1990, and the efforts of tens of thousands of scientists worldwide, no human climate signal has yet been detected that is distinct from natural variation" - Bob Carter, Research Professor of Geology, James Cook University, Townsville

"Currently, China and India combined emit 20 times as much as Australia each day, and that factor is increasing rapidly. Australia's annual savings by 2020 could be emitted by China and India within five days" - Dr. David Evans former Govt Climate Adviser.

“What I see is a country bravely beating along to the agenda of some ideological people, in this case the socialist left of the ALP and the Greens, to take away what is a natural advantage. At the end of the day, we are paying someone else to use our coal” - Peter Costello, former Federal Treasurer - http://tinyurl.com/costello-carbon-tax

“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[felix_unger]

On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?

no, unfortunately

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

"Julia finally got something right. Older people don't vote Labor, because they have seen too many incompetent, mismanaging, money-wasting Labor governments"

“It doesn't matter [who the leader is] the Labor Party is rotten, the policies stink, the lies insufferable, and the waste intolerable. The Muppets could do a better job!”

“All that's needed now is a small miracle to rid us of the worst prime minister and the worst government in Australia's history”

"If the WORLD as a whole cut ALL emissions tomorrow, the average temperature of the planet's not going to drop for several hundred years, perhaps over on thousand years" - Tim Flannery, Climate Commissioner

"It is a remarkable fact that despite the worldwide expenditure of perhaps US$50 billion since 1990, and the efforts of tens of thousands of scientists worldwide, no human climate signal has yet been detected that is distinct from natural variation" - Bob Carter, Research Professor of Geology, James Cook University, Townsville

"Currently, China and India combined emit 20 times as much as Australia each day, and that factor is increasing rapidly. Australia's annual savings by 2020 could be emitted by China and India within five days" - Dr. David Evans former Govt Climate Adviser.

“What I see is a country bravely beating along to the agenda of some ideological people, in this case the socialist left of the ALP and the Greens, to take away what is a natural advantage. At the end of the day, we are paying someone else to use our coal” - Peter Costello, former Federal Treasurer - http://tinyurl.com/costello-carbon-tax

“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[atec77]

On 25/02/2012 3:04 PM, felix_unger wrote:

On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely

--









X-No-Archive: Yes

 

[felix_unger]

On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I don't
know of one that is good enough yet. at present I put up with the one I
have, despite the interference, because of it's audio and video quality.
btw.. I use monster leads, and one I tried from Aldi would not work with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!

can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

"Julia finally got something right. Older people don't vote Labor, because they have seen too many incompetent, mismanaging, money-wasting Labor governments"

“It doesn't matter [who the leader is] the Labor Party is rotten, the policies stink, the lies insufferable, and the waste intolerable. The Muppets could do a better job!”

“All that's needed now is a small miracle to rid us of the worst prime minister and the worst government in Australia's history”

"If the WORLD as a whole cut ALL emissions tomorrow, the average temperature of the planet's not going to drop for several hundred years, perhaps over on thousand years" - Tim Flannery, Climate Commissioner

"It is a remarkable fact that despite the worldwide expenditure of perhaps US$50 billion since 1990, and the efforts of tens of thousands of scientists worldwide, no human climate signal has yet been detected that is distinct from natural variation" - Bob Carter, Research Professor of Geology, James Cook University, Townsville

"Currently, China and India combined emit 20 times as much as Australia each day, and that factor is increasing rapidly. Australia's annual savings by 2020 could be emitted by China and India within five days" - Dr. David Evans former Govt Climate Adviser.

“What I see is a country bravely beating along to the agenda of some ideological people, in this case the socialist left of the ALP and the Greens, to take away what is a natural advantage. At the end of the day, we are paying someone else to use our coal” - Peter Costello, former Federal Treasurer - http://tinyurl.com/costello-carbon-tax

“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[Rob]

On 25/02/2012 12:47 PM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Just like to mention that I have a Strong and could not use the supplied
cable to connect it to the TV as I was getting a hum through the audio.
Ended up using a HDMI cable which resolved the issue.

This is what I found with the Strong equipment - its only a comment.

 

[Don McKenzie]

On 25-Feb-12 12:47 PM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's on the 2.4ghz band I get a lot of interference.
Does anyone know any way to filter the signal? The AC is filtered via a power board. Or alternatively can anyone
recommend a VERY good sender with IR control that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as good as the one I have, which is On-for-All
brand. thanks.

Went down the same road, and eventually settled on a 2 channel good quality modulator:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=157

I send cable TV down one channel, and my CCTV system down the other.

Allows you to use any TV set for cable, or CCTV monitoring.

Requires a little extra to make it work:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=2672

and a little rewiring, so that you have the modulator feeding everything, but if you want to spend the time and money,
you will end up with a top result.


Cheers Don...

=========================

--
Don McKenzie

Dontronics: http://www.dontronics-shop.com/

DuinoMite the PIC32 $35 Basic Computer-MicroController
http://www.dontronics-shop.com/the-maximite-computer.html
Just add a VGA monitor or TV, and PS2 Keyboard.
Arduino Shield, Programmed in Basic, or C.

 

[atec77]

On 25/02/2012 9:25 PM, felix_unger wrote:

On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I don't
know of one that is good enough yet. at present I put up with the one I
have, despite the interference, because of it's audio and video quality.
btw.. I use monster leads, and one I tried from Aldi would not work with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely



Obviously hard wire is the right solution but if you don't have the

license it can cost , I do so n/p

--









X-No-Archive: Yes

 

[felix_unger]

On 26-February-2012 8:16 AM, atec77 wrote:

On 25/02/2012 9:25 PM, felix_unger wrote:
On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR
control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none
are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I don't
know of one that is good enough yet. at present I put up with the one I
have, despite the interference, because of it's audio and video quality.
btw.. I use monster leads, and one I tried from Aldi would not work with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely



Obviously hard wire is the right solution

how do you 'hard wire' CVBS for a long run?

but if you don't have the license it can cost , I do so n/p

license?

--
rgds,

Pete
-------
“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[felix_unger]

On 26-February-2012 6:44 AM, Don McKenzie wrote:

On 25-Feb-12 12:47 PM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's on the 2.4ghz band I get a lot of interference.
Does anyone know any way to filter the signal? The AC is filtered via
a power board. Or alternatively can anyone
recommend a VERY good sender with IR control that isn't subject to
audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are
as good as the one I have, which is On-for-All
brand. thanks.


Went down the same road, and eventually settled on a 2 channel good
quality modulator:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=157


I send cable TV down one channel, and my CCTV system down the other.

Allows you to use any TV set for cable, or CCTV monitoring.

Requires a little extra to make it work:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=2672


and a little rewiring, so that you have the modulator feeding
everything, but if you want to spend the time and money, you will end
up with a top result.


Cheers Don...

=========================

wow! this looks interesting. I'll follow up on it. Thanks Don!

--
rgds,

Pete
-------
“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[felix_unger]

On 25-February-2012 10:58 PM, Rob wrote:

On 25/02/2012 12:47 PM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because it's
on the 2.4ghz band I get a lot of interference. Does anyone know any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR control
that isn't subject to audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are as
good as the one I have, which is On-for-All brand. thanks.



Just like to mention that I have a Strong and could not use the
supplied cable to connect it to the TV as I was getting a hum through
the audio. Ended up using a HDMI cable which resolved the issue.

you must be talking about a STB or PVR. their AV sender only has
composite output

This is what I found with the Strong equipment - its only a comment.

noted, thanks

--
rgds,

Pete
-------
“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[felix_unger]

On 26-February-2012 11:36 AM, felix_unger wrote:

On 26-February-2012 6:44 AM, Don McKenzie wrote:

On 25-Feb-12 12:47 PM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's on the 2.4ghz band I get a lot of interference.
Does anyone know any way to filter the signal? The AC is filtered
via a power board. Or alternatively can anyone
recommend a VERY good sender with IR control that isn't subject to
audio/video interference? I have tried the Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none are
as good as the one I have, which is On-for-All
brand. thanks.


Went down the same road, and eventually settled on a 2 channel good
quality modulator:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=157


I send cable TV down one channel, and my CCTV system down the other.

Allows you to use any TV set for cable, or CCTV monitoring.

Requires a little extra to make it work:
http://www.electrocraft.com.au/Products/EC_StockInformation.asp?stockNo=2672


and a little rewiring, so that you have the modulator feeding
everything, but if you want to spend the time and money, you will end
up with a top result.


Cheers Don...

=========================


wow! this looks interesting. I'll follow up on it. Thanks Don!

p.s. can I assume that the AV quality is as good as normal FTA UHF?

--
rgds,

Pete
-------
“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[Petzl]

On Sun, 26 Feb 2012 11:40:29 +1100, felix_unger <me@nothere.com>
wrote:

wow! this looks interesting. I'll follow up on it. Thanks Don!


p.s. can I assume that the AV quality is as good as normal FTA UHF?

Mine worked without interferance on all five channels
http://www.electrosmog.com.au/live/default.htm
Might be time to move house
--
Petzl
Chattanooga choo choo
http://www.dailymotion.com/video/x1d2em_chattanooga-choo-choo_fun

 

[atec77]

On 26/02/2012 10:34 AM, felix_unger wrote:

On 26-February-2012 8:16 AM, atec77 wrote:

On 25/02/2012 9:25 PM, felix_unger wrote:
On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR
control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none
are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I don't
know of one that is good enough yet. at present I put up with the one I
have, despite the interference, because of it's audio and video quality.
btw.. I use monster leads, and one I tried from Aldi would not work with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely



Obviously hard wire is the right solution

how do you 'hard wire' CVBS for a long run?
do away with most of the link adding cabled connections from the source

but if you don't have the license it can cost , I do so n/p


license?
cablers permit

--









X-No-Archive: Yes

 

[felix_unger]

On 26-February-2012 1:29 PM, atec77 wrote:

On 26/02/2012 10:34 AM, felix_unger wrote:
On 26-February-2012 8:16 AM, atec77 wrote:

On 25/02/2012 9:25 PM, felix_unger wrote:
On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR
control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none
are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I
don't
know of one that is good enough yet. at present I put up with the
one I
have, despite the interference, because of it's audio and video
quality.
btw.. I use monster leads, and one I tried from Aldi would not work
with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely



Obviously hard wire is the right solution

how do you 'hard wire' CVBS for a long run?
do away with most of the link adding cabled connections from the source

specifically what are you referring to?

but if you don't have the license it can cost , I do so n/p


license?
cablers permit

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

"Julia finally got something right. Older people don't vote Labor, because they have seen too many incompetent, mismanaging, money-wasting Labor governments"

“It doesn't matter [who the leader is] the Labor Party is rotten, the policies stink, the lies insufferable, and the waste intolerable. The Muppets could do a better job!”

“All that's needed now is a small miracle to rid us of the worst prime minister and the worst government in Australia's history”

"If the WORLD as a whole cut ALL emissions tomorrow, the average temperature of the planet's not going to drop for several hundred years, perhaps over on thousand years" - Tim Flannery, Climate Commissioner

"It is a remarkable fact that despite the worldwide expenditure of perhaps US$50 billion since 1990, and the efforts of tens of thousands of scientists worldwide, no human climate signal has yet been detected that is distinct from natural variation" - Bob Carter, Research Professor of Geology, James Cook University, Townsville

"Currently, China and India combined emit 20 times as much as Australia each day, and that factor is increasing rapidly. Australia's annual savings by 2020 could be emitted by China and India within five days" - Dr. David Evans former Govt Climate Adviser.

“What I see is a country bravely beating along to the agenda of some ideological people, in this case the socialist left of the ALP and the Greens, to take away what is a natural advantage. At the end of the day, we are paying someone else to use our coal” - Peter Costello, former Federal Treasurer - http://tinyurl.com/costello-carbon-tax

“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”

 

[atec77]

On 26/02/2012 3:48 PM, felix_unger wrote:

On 26-February-2012 1:29 PM, atec77 wrote:

On 26/02/2012 10:34 AM, felix_unger wrote:
On 26-February-2012 8:16 AM, atec77 wrote:

On 25/02/2012 9:25 PM, felix_unger wrote:
On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR
control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none
are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I
don't
know of one that is good enough yet. at present I put up with the
one I
have, despite the interference, because of it's audio and video
quality.
btw.. I use monster leads, and one I tried from Aldi would not work
with
them. because they had such low signal loss they overloaded the input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise source
and move it in frequency or remove it completely



Obviously hard wire is the right solution

how do you 'hard wire' CVBS for a long run?
do away with most of the link adding cabled connections from the source

specifically what are you referring to?


but if you don't have the license it can cost , I do so n/p


license?
cablers permit





move the radio closer , and to connect it back to the router or source

you run a longer cable

--









X-No-Archive: Yes

 

[felix_unger]

On 26-February-2012 6:13 PM, atec77 wrote:

On 26/02/2012 3:48 PM, felix_unger wrote:
On 26-February-2012 1:29 PM, atec77 wrote:

On 26/02/2012 10:34 AM, felix_unger wrote:
On 26-February-2012 8:16 AM, atec77 wrote:

On 25/02/2012 9:25 PM, felix_unger wrote:
On 25-February-2012 9:36 PM, atec77 wrote:

On 25/02/2012 3:04 PM, felix_unger wrote:
On 25-February-2012 1:22 PM, atec77 wrote:

On 25/02/2012 11:47 AM, felix_unger wrote:

I have a good AV sender. The picture is great, except that
because
it's
on the 2.4ghz band I get a lot of interference. Does anyone know
any way
to filter the signal? The AC is filtered via a power board. Or
alternatively can anyone recommend a VERY good sender with IR
control
that isn't subject to audio/video interference? I have tried the
Strong
5.8ghz one, and the Cocoon digital and 2.4 ghz models, and none
are as
good as the one I have, which is On-for-All brand. thanks.

Is it possible to move the frequency ?


no, unfortunately

Sell it and buy one that will

well you'll see in my post that I'm asking for recommendations. I
don't
know of one that is good enough yet. at present I put up with the
one I
have, despite the interference, because of it's audio and video
quality.
btw.. I use monster leads, and one I tried from Aldi would not work
with
them. because they had such low signal loss they overloaded the
input.
you had to use the skinny crappy ones that came with it!


can't see another solution unless you can find the major noise
source
and move it in frequency or remove it completely



Obviously hard wire is the right solution

how do you 'hard wire' CVBS for a long run?
do away with most of the link adding cabled connections from the source

specifically what are you referring to?


but if you don't have the license it can cost , I do so n/p


license?
cablers permit





move the radio closer , and to connect it back to the router or source
you run a longer cable

seems you don't know what we're talking about

--
rgds,

Pete
-------
“If Julia is the answer, then what was the stupid question?!”

"Julia finally got something right. Older people don't vote Labor, because they have seen too many incompetent, mismanaging, money-wasting Labor governments"

“It doesn't matter [who the leader is] the Labor Party is rotten, the policies stink, the lies insufferable, and the waste intolerable. The Muppets could do a better job!”

“All that's needed now is a small miracle to rid us of the worst prime minister and the worst government in Australia's history”

"If the WORLD as a whole cut ALL emissions tomorrow, the average temperature of the planet's not going to drop for several hundred years, perhaps over on thousand years" - Tim Flannery, Climate Commissioner

"It is a remarkable fact that despite the worldwide expenditure of perhaps US$50 billion since 1990, and the efforts of tens of thousands of scientists worldwide, no human climate signal has yet been detected that is distinct from natural variation" - Bob Carter, Research Professor of Geology, James Cook University, Townsville

"Currently, China and India combined emit 20 times as much as Australia each day, and that factor is increasing rapidly. Australia's annual savings by 2020 could be emitted by China and India within five days" - Dr. David Evans former Govt Climate Adviser.

“What I see is a country bravely beating along to the agenda of some ideological people, in this case the socialist left of the ALP and the Greens, to take away what is a natural advantage. At the end of the day, we are paying someone else to use our coal” - Peter Costello, former Federal Treasurer - http://tinyurl.com/costello-carbon-tax

“Wayne Swan threatening the Banks, is a bit like being savaged by a dead sheep!”