[IIYAMA] vision master pro 450 A901HT

P

Pierre Merriaux

Guest
Hi,

I have a dead CRT from Iiyama but all parts are manufactured by
mitsubishi.
Symptoms : After power on, the screen light its led for 1/2 - 1 second
then turn off this led.
After a little investigation, I noticed that when I unplug a cable from
the main board (near a microcontroller) to the little board connected to the
CRT, the led stay on.

Anyone have seen this before ?

Perhaps some of you have an appropriate schematic (or service manual) for
this screen or for the same type of screen from mitsubishi.

I took some pictures : http://lerhu.free.fr/iiyama

Thanks,
 
This may be of use:

http://home.clara.net/adrian-smith31/pctips/monitor_tips.htm#Iiyama

Hellraiser..........>

"Pierre Merriaux" <pierre.merriaux@wanadoo.fr> wrote in message
news:bekdhh$t5t$1@news-reader3.wanadoo.fr...
Hi,

I have a dead CRT from Iiyama but all parts are manufactured by
mitsubishi.
Symptoms : After power on, the screen light its led for 1/2 - 1 second
then turn off this led.
After a little investigation, I noticed that when I unplug a cable from
the main board (near a microcontroller) to the little board connected to
the
CRT, the led stay on.

Anyone have seen this before ?

Perhaps some of you have an appropriate schematic (or service manual) for
this screen or for the same type of screen from mitsubishi.

I took some pictures : http://lerhu.free.fr/iiyama

Thanks,
 
"Pierre Merriaux" <pierre.merriaux@wanadoo.fr> wrote in message
news:bekdhh$t5t$1@news-reader3.wanadoo.fr...
Hi,

I have a dead CRT from Iiyama but all parts are manufactured by
mitsubishi.
Symptoms : After power on, the screen light its led for 1/2 - 1 second
then turn off this led.
After a little investigation, I noticed that when I unplug a cable from
the main board (near a microcontroller) to the little board connected to
the
CRT, the led stay on.

Anyone have seen this before ?

Perhaps some of you have an appropriate schematic (or service manual)
for
this screen or for the same type of screen from mitsubishi.

I took some pictures : http://lerhu.free.fr/iiyama
Incidentally, on a slightly different note, if any of you have a Vision
Master Pro 510 (A201HT) that powers on but gives no picture, replace the
2SC5570 (Q503 I think it is) and the fusible resistor R561. Worked fine for
me, I'm now enjoying 20" of flat screened loveliness :)

Hellraiser............>
 
"Pierre Merriaux" <pierre.merriaux@wanadoo.fr> wrote in message
news:bekdhh$t5t$1@news-reader3.wanadoo.fr...
Hi,

I have a dead CRT from Iiyama but all parts are manufactured by
mitsubishi.
Symptoms : After power on, the screen light its led for 1/2 - 1 second
then turn off this led.
After a little investigation, I noticed that when I unplug a cable from
the main board (near a microcontroller) to the little board connected to
the
CRT, the led stay on.

Anyone have seen this before ?

Perhaps some of you have an appropriate schematic (or service manual) for
this screen or for the same type of screen from mitsubishi.

I took some pictures : http://lerhu.free.fr/iiyama

Thanks,
There's not much to go on, it could be a failed HOT, a PSU fault or heaven
knows what else. One thing for certain, powering on your monitor with
unplugged connectors is asking for a whole load of trouble.

Dave
 

Welcome to EDABoard.com

Sponsor

Back
Top