Goto page 1, 2 Next
Phil Allison
Guest
Wed Dec 14, 2011 2:07 am
** Hi,
I have a VOX AC100cp ( Chines made) on the bench - it is about 6 years old.
It has all its original parts but is in a very bad way. The known faults
are:
1. One (Ruby) EL34 has lost vacuum.
2. Two scorched 5W screen resistors, one detached from the PCB.
3. One blown HT fuse, a 1 amp slow blow - which may well not be the only
one.
4. Output tranny OPEN on one side of the primary and exhibiting symptoms of
shorted turns.
5. Bridge rectifier only conducting on one half cycle - giving 50Hz
ripple.
The scorched 5W resistors are on the side with the open tranny winding.
The EL34 with no vacuum is on the other side.
Wanna have a go at the sequence of failures ?
.... Phil
Bitrex
Guest
Wed Dec 14, 2011 8:32 am
On 12/13/2011 8:07 PM, Phil Allison wrote:
Quote:
** Hi,
I have a VOX AC100cp ( Chines made) on the bench - it is about 6 years old.
It has all its original parts but is in a very bad way. The known faults
are:
1. One (Ruby) EL34 has lost vacuum.
2. Two scorched 5W screen resistors, one detached from the PCB.
3. One blown HT fuse, a 1 amp slow blow - which may well not be the only
one.
4. Output tranny OPEN on one side of the primary and exhibiting symptoms of
shorted turns.
5. Bridge rectifier only conducting on one half cycle - giving 50Hz
ripple.
The scorched 5W resistors are on the side with the open tranny winding.
The EL34 with no vacuum is on the other side.
Wanna have a go at the sequence of failures ?
... Phil
Is this the output stage in question, on page 5 (assuming the head and
the combo are constructed the same)?
http://www.ampix.org/albums/userpics/10003/Vox_AC100CPH.pdf
It looks like there are a few bridge rectifiers in the circuit, one for
the solid state preamp stuff, one for the output tube bias, and one for
the preamp heaters. Which one failed?
It would seem that a loss of bias on the output tubes might account for
some of the problems, but I'm guessing that you've already considered
that and that the failure mode may actually be more subtle.
Phil Allison
Guest
Wed Dec 14, 2011 9:14 am
"Bitrex"
Quote:
It looks like there are a few bridge rectifiers in the circuit, one for
the solid state preamp stuff, one for the output tube bias, and one for
the preamp heaters. Which one failed?
** Never said any bridges had failed.
There is 50Hz ripple on the HT, of course.
Since my post I discovered that R107 ( 22 ohms 7W) is open - this is is
series with the high voltage secondary.
All other supplies are OK.
.... Phil
Gareth Magennis
Guest
Wed Dec 14, 2011 11:03 am
"Phil Allison" <phil_a_at_tpg.com.au> wrote in message
news:9kqb60FhpkU1_at_mid.individual.net...
Quote:
** Hi,
I have a VOX AC100cp ( Chines made) on the bench - it is about 6 years
old. It has all its original parts but is in a very bad way. The known
faults are:
1. One (Ruby) EL34 has lost vacuum.
2. Two scorched 5W screen resistors, one detached from the PCB.
3. One blown HT fuse, a 1 amp slow blow - which may well not be the only
one.
4. Output tranny OPEN on one side of the primary and exhibiting symptoms
of shorted turns.
5. Bridge rectifier only conducting on one half cycle - giving 50Hz
ripple.
The scorched 5W resistors are on the side with the open tranny winding.
The EL34 with no vacuum is on the other side.
Wanna have a go at the sequence of failures ?
... Phil
Well my uneducated guess is that it had to have started with the tube with
the lost vacuum.
Don't know what the normal subsequent failuire mode is, but I suspect either
the tube would short Anode to ground via heater cirduit perhaps, or would
just send the bias way off the planet.
Huge DC through the OPT primary partly via the scorched grid resistors on
the other side, and a nasty expensive smell.
Poo.
Gareth.
Gareth Magennis
Guest
Wed Dec 14, 2011 11:12 am
Or maybe,
duff tube shorted some windings thorugh DC.. The amp was being played at
the time, so the "good" tubes shorted their windings too but via AC.
Hey, this is a good game.
Gareth.
Phil Allison
Guest
Wed Dec 14, 2011 11:39 am
"Gareth Magennis"
Quote:
Huge DC through the OPT primary partly via the scorched grid resistors on
the other side, and a nasty expensive smell.
** The HT fuse prevents huge DC through the output transformer primary.
I suggest you read the list of failures again.
The thing is to work out what part failed FIRST and how that led to each of
the others.
.... Phil
Phil Allison
Guest
Wed Dec 14, 2011 11:52 am
"Bitrex"
Quote:
http://www.ampix.org/albums/userpics/10003/Vox_AC100CPH.pdf
** Where did you find that link ?
Recent model VOX schems and service manuals are hard to find.
.... Phil
Bitrex
Guest
Wed Dec 14, 2011 11:59 am
On 12/14/2011 5:52 AM, Phil Allison wrote:
Quote:
A Google search for "vox ac100cph service manual filetype:pdf" brings it
up. Since most service manuals online are in PDF format, adding the
filetype qualifier helps sift through the cruft.
Gareth Magennis
Guest
Wed Dec 14, 2011 12:11 pm
"Phil Allison" <phil_a_at_tpg.com.au> wrote in message
news:9krcndFoahU1_at_mid.individual.net...
Quote:
"Gareth Magennis"
Huge DC through the OPT primary partly via the scorched grid resistors on
the other side, and a nasty expensive smell.
** The HT fuse prevents huge DC through the output transformer primary.
I suggest you read the list of failures again.
The thing is to work out what part failed FIRST and how that led to each
of the others.
... Phil
I don't really know enough to achieve that, Phil.
I would guess again though that it started with the duff valve, which put
excessive DC through its side of the transformer, maybe not enough to blow
the fuse at first.. This would saturate the core and overheat the OPT.
I guess the owner kept playing the amp in this sorry state, leading to the
demise of the other 2 valves and their windings. He may even have
disconnected the speaker, or had an intermittent speaker connection, or even
swapped output valves around., causing even more damage.
Gareth.
Phil Allison
Guest
Wed Dec 14, 2011 12:45 pm
"Gareth Magennis"
Quote:
"Phil Allison"
** The HT fuse prevents huge DC through the output transformer primary.
I suggest you read the list of failures again.
The thing is to work out what part failed FIRST and how that led to each
of the others.
I don't really know enough to achieve that, Phil.
** You had better sit and watch this one then.
Quote:
I would guess again though that it started with the duff valve,
** Hint - how did one half of the OT primary go open ?
... Phil
Gareth Magennis
Guest
Wed Dec 14, 2011 2:19 pm
"Phil Allison" <phil_a_at_tpg.com.au> wrote in message
news:9krgk0FmbfU1_at_mid.individual.net...
Quote:
"Gareth Magennis"
"Phil Allison"
** The HT fuse prevents huge DC through the output transformer primary.
I suggest you read the list of failures again.
The thing is to work out what part failed FIRST and how that led to each
of the others.
I don't really know enough to achieve that, Phil.
** You had better sit and watch this one then.
I would guess again though that it started with the duff valve,
** Hint - how did one half of the OT primary go open ?
... Phil
Coca-cola spilt through the grille?! Might also have cracked the valve.
(I'm kind of an Occam's Razor / the customer is a Numpty kind of guy)
Gareth.
Phil Allison
Guest
Wed Dec 14, 2011 11:16 pm
"Gareth Magennis"
Quote:
Coca-cola spilt through the grille?!
** Not tricks here - I have detailed all the faults and there is no sign
of any such damage.
.... Phil
Gareth Magennis
Guest
Thu Dec 15, 2011 12:36 am
"Phil Allison" <phil_a_at_tpg.com.au> wrote in message
news:9kslieFavU1_at_mid.individual.net...
Quote:
"Gareth Magennis"
Coca-cola spilt through the grille?!
** Not tricks here - I have detailed all the faults and there is no sign
of any such damage.
... Phil
Well, one last try before I give up then.
The "lost vacuum" tube probably just went out of circuit, leaving one valve
vs. two.
I think I'm right in saying that this will produce a net DC field in the OPT
primary that would push it towards saturation and overheating.
The amp was kept in use at high power with this fault.
So, the "two valve" primary winding got very hot, shorted some turns, then
went open circuit. This meant that its Screen Grids became the Anodes,
which got overloaded until the resistors burnt or fell off the PCB.
Half of the Bridge rectifier may well have burnt out in the process of
burning out the screen grid resistors - at some point the HT fuse would
finally blow, halting the whole process.
(Or the customer could have replaced the blown HT fuse with a higher rated
one, then put the original back in before handing it in for repair).
There might be other problems due to disconnection of speaker, or arcing
inside the OPT connecting secondary and primary, that might force HT back to
the output circuitry, I don't see any "flyback protection diodes" or
whatever they are properly called, in the schematic.
That's just about the limit of my knowledge of failure modes of valve amps
I'm afraid.
Gareth.
Phil Allison
Guest
Thu Dec 15, 2011 12:50 am
"Gareth Magennis"
Quote:
Well, one last try before I give up then.
The "lost vacuum" tube probably just went out of circuit, leaving one
valve vs. two.
** When a power tube loses vacuum, it usually conducts very heavily
regardless of grid bias setting. The *low pressure* gas inside ionises with
applied DC and it is lights up like a neon tube.
Quote:
I think I'm right in saying that this will produce a net DC field in the
OPT primary that would push it towards saturation and overheating.
** This is a large transformer and it would normally have almost no temp
rise in operation - the primary resistance is 20 ohms per side. Even under
fault conditions, the 1 amp HT fuse protects it from damage.
Quote:
So, the "two valve" primary winding got very hot, shorted some turns, then
went open circuit.
** With any large OT - this is a very unlikely scenario.
Quote:
This meant that its Screen Grids became the Anodes, which got overloaded
until the resistors burnt or fell off the PCB.
** This is correct.
Quote:
Half of the Bridge rectifier may well have burnt out
** Read the thread again. There are no faulty bridges.
Quote:
(Or the customer could have replaced the blown HT fuse with a higher rated
one, then put the original back in before handing it in for repair).
** I figure more than one HT fuse has blown, but the one in the holder
looked like the original.
Quote:
There might be other problems due to disconnection of speaker, or arcing
inside the OPT
** Now you are getting warm...
Quote:
connecting secondary and primary
** No way is that the case here.
.... Phil
Gareth Magennis
Guest
Thu Dec 15, 2011 8:34 pm
"Phil Allison" <phil_a_at_tpg.com.au> wrote in message
news:9ksr2oF9hiU1_at_mid.individual.net...
Quote:
"Gareth Magennis"
Well, one last try before I give up then.
The "lost vacuum" tube probably just went out of circuit, leaving one
valve vs. two.
** When a power tube loses vacuum, it usually conducts very heavily
regardless of grid bias setting. The *low pressure* gas inside ionises
with applied DC and it is lights up like a neon tube.
I think I'm right in saying that this will produce a net DC field in the
OPT primary that would push it towards saturation and overheating.
** This is a large transformer and it would normally have almost no temp
rise in operation - the primary resistance is 20 ohms per side. Even under
fault conditions, the 1 amp HT fuse protects it from damage.
So, the "two valve" primary winding got very hot, shorted some turns,
then went open circuit.
** With any large OT - this is a very unlikely scenario.
This meant that its Screen Grids became the Anodes, which got overloaded
until the resistors burnt or fell off the PCB.
** This is correct.
Half of the Bridge rectifier may well have burnt out
** Read the thread again. There are no faulty bridges.
(Or the customer could have replaced the blown HT fuse with a higher
rated one, then put the original back in before handing it in for
repair).
** I figure more than one HT fuse has blown, but the one in the holder
looked like the original.
There might be other problems due to disconnection of speaker, or arcing
inside the OPT
** Now you are getting warm...
connecting secondary and primary
** No way is that the case here.
... Phil
Well, are you going to tell us then?
Final answer - some problem with the speaker connection fed back 2 x HT
voltage all the way back to the mains transformer.
The customer DID replace the HT fuse with one of higher rating, ran the amp
again, and caused lots more damage. He put the original blown fuse back in
place before handing it in, in the hope you wouldn't realise what a Numpty
he is.
:)
Gareth.
Goto page 1, 2 Next
