EDAboard.com | EDAboard.de | EDAboard.co.uk | WTWH Media

Handheld LCR meters, any good?

Ask a question - edaboard.com

elektroda.net NewsGroups Forum Index - Electronics Equipment - Handheld LCR meters, any good?

bob prohaska
Guest

Mon Mar 16, 2020 8:45 pm   



There are now some handheld inductance/capacitance/resistance
measuring tools that are comparable in price to a traditional
digital VOM. Are they good enough to be of use in typical
troublshooting situations like motors, alternators and ignition
systems? In other words, no RF.

Amazon has one for only $35, which seems hard to believe. One
review notes lack of overload protection, perhaps explaining
the low price, but still it's said to work reasonably well.
Even if a unit with decent overload protection doubles the
price that seems inexpensive, if it really works.

My only experience with LCR measurements was with a General
Radio manual bridge probably built in the 1960's. Excellent,
but bulky.

Thanks for reading, and any guidance!

bob prohaska

Ralph Mowery
Guest

Mon Mar 16, 2020 8:45 pm   



In article <r4oj5g$ag3$1_at_news.albasani.net>, bp_at_www.zefox.net says...
Quote:
There are now some handheld inductance/capacitance/resistance
measuring tools that are comparable in price to a traditional
digital VOM. Are they good enough to be of use in typical
troublshooting situations like motors, alternators and ignition
systems? In other words, no RF.

A


Ebay has some for about $ 20. I have one I bought several years ago and
it works fine to give the value of the components.

A company called Peak is selling them for close to $ 100,but internally
they are all about the same.

I don't know what you mean by trouble shooting with them,, but for out
of circuit test on components they are fine to tell if a component is
good or bad and will show close to the actual value of the component.

Computer Nerd Kev
Guest

Mon Mar 16, 2020 11:45 pm   



bob prohaska <bp_at_www.zefox.net> wrote:
Quote:
There are now some handheld inductance/capacitance/resistance
measuring tools that are comparable in price to a traditional
digital VOM. Are they good enough to be of use in typical
troublshooting situations like motors, alternators and ignition
systems? In other words, no RF.

Amazon has one for only $35, which seems hard to believe. One
review notes lack of overload protection, perhaps explaining
the low price, but still it's said to work reasonably well.
Even if a unit with decent overload protection doubles the
price that seems inexpensive, if it really works.


I looked into these a while ago but didn't actually buy one (can't
remember my reasoning anymore). At that point the ones around that
price sold with a rectangular PCB with a fiarly large mono LCD
display mounted on it, were based on an open-source design that was
well documented in a PDF available somewhere on the web. That
described the circuit as well as the measurement performance.

I think you found the design by searching for the author's name. I've
long forgotten what that was now, and it isn't standing out in a
quick search for "DIY LCR meter". I probably still have the PDF filed
away some where. I'll try to remember to have a look sometime if you
haven't figured it out for yourself.

Quote:
My only experience with LCR measurements was with a General
Radio manual bridge probably built in the 1960's. Excellent,
but bulky.


Instead of a bridge, these use a microcontroller to time the
charge/discharge rate (there's a bit more to it than just a timer,
but that's the basic principle). This is a valid technique used in
many high-end LCR meters since the introduction of microcontrollers.
I don't remember the details of how well it was implemented in this
design, or how cheap Chinese components might affect the accuracy. I
think the original design was fairly decent though.

--
__ __
#_ < |\| |< _#

bob prohaska
Guest

Mon Mar 16, 2020 11:45 pm   



Ralph Mowery <rmowery28146_at_earthlink.net> wrote:
Quote:
In article <r4oj5g$ag3$1_at_news.albasani.net>, bp_at_www.zefox.net says...
There are now some handheld inductance/capacitance/resistance
measuring tools that are comparable in price to a traditional
digital VOM. Are they good enough to be of use in typical
troublshooting situations like motors, alternators and ignition
systems? In other words, no RF.

A


Ebay has some for about $ 20. I have one I bought several years ago and
it works fine to give the value of the components.

A company called Peak is selling them for close to $ 100,but internally
they are all about the same.

I don't know what you mean by trouble shooting with them,, but for out
of circuit test on components they are fine to tell if a component is
good or bad and will show close to the actual value of the component.


Sounds like they're reasonably useful. By trouble shooting I meant simply
that the device is reasonably unfussy in use. It needn't be highly accurate,
and ideally should measure in-cicuit, but the latter is probably unrealistic.
In my case out-of-circuit measurements are apt to be the norm. It's also
helpful if the L and C measurements don't require a large Q value.

One thing that made me a little wary is the apparent lack of offerings from
Tektronix and Fluke.

Thanks for replying,

bob prohaska

Ralph Mowery
Guest

Tue Mar 17, 2020 12:45 am   



In article <r4otj4$ksf$1_at_news.albasani.net>, bp_at_www.zefox.net says...
Quote:

Sounds like they're reasonably useful. By trouble shooting I meant simply
that the device is reasonably unfussy in use. It needn't be highly accurate,
and ideally should measure in-cicuit, but the latter is probably unrealistic.
In my case out-of-circuit measurements are apt to be the norm. It's also
helpful if the L and C measurements don't require a large Q value.




YOu can get them from about $ 15 to $ 50 depending on the case and if
you want to get them direct from China or faster from someone in the US.
Even less if no case or leads.

The one I have is accurate enough to tell if a component is good or bad.
Probably as good as any tester that is not lab grade. They do not
usually work in circuit.

They usually have 3 leads and you just hook them up in any order, use
only 2 if that is all the component has. Then press the button and a
few seconds later it will tell you what is hooked to the leads and the
value.

bob prohaska
Guest

Tue Mar 17, 2020 3:45 am   



Ralph Mowery <rmowery28146_at_earthlink.net> wrote:
Quote:

They usually have 3 leads and you just hook them up in any order, use
only 2 if that is all the component has. Then press the button and a
few seconds later it will tell you what is hooked to the leads and the
value.


Any idea how the measurement is made? Everything I can think of
starts with a step voltage and records voltage and current. That
takes something akin to a DSO and waveform analyzer to sort out
the circuit values. Seems incredible for less than $50.

Thanks for writing!

bob prohaska

Charlie+
Guest

Tue Mar 17, 2020 8:45 am   



On Tue, 17 Mar 2020 01:52:23 +0000 (UTC), bob prohaska
<bp_at_www.zefox.net> wrote as underneath :

Quote:
Ralph Mowery <rmowery28146_at_earthlink.net> wrote:

They usually have 3 leads and you just hook them up in any order, use
only 2 if that is all the component has. Then press the button and a
few seconds later it will tell you what is hooked to the leads and the
value.


Any idea how the measurement is made? Everything I can think of
starts with a step voltage and records voltage and current. That
takes something akin to a DSO and waveform analyzer to sort out
the circuit values. Seems incredible for less than $50.

See youtube for lots of info on the cheap units, there are lots,
following similar design. They do not work on very low C or L values
thus can mislead if you are unaware - but otherwise unbeatable for
value. No incircuit at all, Bob Parker Blue ESR meter for that in Caps
only of course, but getting up the price scale. C+

Ralph Mowery
Guest

Tue Mar 17, 2020 3:45 pm   



In article <r4pagn$kb4$1_at_news.albasani.net>, bp_at_www.zefox.net says...
Quote:

Any idea how the measurement is made? Everything I can think of
starts with a step voltage and records voltage and current. That
takes something akin to a DSO and waveform analyzer to sort out
the circuit values. Seems incredible for less than $50.



There is not too much to them. Mostly a microprocessor and software .

Look at this url. You may have to hit the 'translate' to get it in
English.

https://www.mikrocontroller.net/articles/AVR_Transistortester

The basic circuit is about $ 10 from China and the other cost is just
the case and leads depending on what you want.

I think it cost me about $ 15 for the basic built circuit board with the
2 line of 16 character display. I did put it in a box and added some
leads. It would have been usable as bought but I just did not want a
bare circuit board laying on the bench. I am thinking of buying one of
the more modern looking ones from China for about $ 25 or less. Not
sure if I will or not as I do not do that much any more and the one I
have works fine.

Rich
Guest

Tue Mar 17, 2020 9:45 pm   



bob prohaska <bp_at_www.zefox.net> wrote:
Quote:
There are now some handheld inductance/capacitance/resistance
measuring tools that are comparable in price to a traditional digital
VOM. Are they good enough to be of use in typical troublshooting
situations like motors, alternators and ignition systems? In other
words, no RF.

Amazon has one for only $35, which seems hard to believe.


I bought this one last year, it is more than $35, from this ebay
seller:

https://www.ebay.com/itm/DER-EE-High-Accuracy-Handheld-LCR-Meter-DE-5000-bundle-TL-21-TL-22-AC-Adapter/312069448188?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649

The reason why I picked this seller is his pack included the AC adaptor
in the kit.

I've been extremely pleased with it. To the extent I can tell,
capacitance measurements are accurate, i.e., new caps measure to well
within their tolerance specs. Resistance measurments are close enough
to my HP3468B in four wire mode that I consider them accurate (or else
two fully separate meters are both identically offset, which I find
unlikely). I've not used the inductance mode enough to form any
opinion.

Bad capacitors (i.e., the infamous swollen top variety) clearly show as
bad.

It will do reasonable in-circuit measurments of capacitors (obviously
depends on the exact circuit connections).

The unit, and the english language booklet (can be located via a web
search) both state to discharge caps before measuring, which implies it
has limited overload/input protection.

So far, for the small amount of troubleshooting I've used it for so
far, I've found it to be quite useful to have.

In Jan. I replaced the very short set of alligator clip wires in the
alligator clip adaptor with a longer set of kelvin clip leads I picked
up from an amazon seller. That was a worthwhile modification.

Computer Nerd Kev
Guest

Tue Mar 17, 2020 11:45 pm   



bob prohaska <bp_at_www.zefox.net> wrote:
Quote:

Any idea how the measurement is made? Everything I can think of
starts with a step voltage and records voltage and current. That
takes something akin to a DSO and waveform analyzer to sort out
the circuit values. Seems incredible for less than $50.


Modern microcontrollers are able to do the voltage and current
measurements with minimal external components. The PDF for the
original open-source project that they're based on described the
measurement process in detail.

I had a look, but I must have deleted it. It's out there to be found
on the web with just a little bit of effort though.

If you find that project, it might be worth checking whether there's
a firmware upgrade available that the Chinese haven't bothered with.
That's the case for a similar open-source signal generator board
that's sold.

--
__ __
#_ < |\| |< _#

elektroda.net NewsGroups Forum Index - Electronics Equipment - Handheld LCR meters, any good?

Ask a question - edaboard.com

Arabic version Bulgarian version Catalan version Czech version Danish version German version Greek version English version Spanish version Finnish version French version Hindi version Croatian version Indonesian version Italian version Hebrew version Japanese version Korean version Lithuanian version Latvian version Dutch version Norwegian version Polish version Portuguese version Romanian version Russian version Slovak version Slovenian version Serbian version Swedish version Tagalog version Ukrainian version Vietnamese version Chinese version Turkish version
EDAboard.com map